1. 2016 Honda Shadow Vtx 600 Service Manual Download

. InstaTrike Installation Manual Honda Shadow 600 Limited Warranty. TOW-PAC, INC. Warrants to the first end user purchaser that this product “InstaTrike” when purchased will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product for the period of one year from date of original purchase. After your InstaTrike is installed, take some time to get used to “Trike” handling characteristics.

On a Trike you will steer rather than lean as you would on a conventional two wheel motorcycle. Take corners very slowly until you get used to the feel of cornering on a Trike.

After your InstaTrike is installed, take some time to get used to “Trike” handling characteristics. On a Trike you will steer rather than lean as you would on a conventional two wheel motorcycle. Take corners very slowly until you get used to the feel of cornering on a Trike.

paved surfaces only. Use of InstaTrike on unpaved terrain may void warranty. When installing trailer hitch attach all bolts and brackets loosely. After all bolts and brackets are in place tighten all bolts. Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position.

Remove saddle bags Install receiver hitch and double check all bolts Remount saddle bags (if applicable) Assemble InstaTrike hitch cart Attach InstaTrike to motorcycle via receiver hitch Attach leanstop brace bolts to receiver hitch Align InstaTrike wheels Double check all bolts for tightness Test ride InstaTrike slowly in an open area to familiarize yourself with handling characteristics Receiver Hitch Installation. Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation.

2016 Honda Shadow Vtx 600 Service Manual Download

After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike. 1) Place motorcycle on a smooth level surface on its side stand. 2) Remove saddle bags. 3) Mount bracket C (left side) to the 2 bolts that attach the rear fender and sub frame to the main motorcycle frame.

12) Tighten all bolts at this time. Receiver Hitch Diagram Leveling stand screw jack installation 1) Thread right side screw jack into leveling stand tab on bracket F and adjust leveling jack bolt out.

2) Push motorcycle over from left side until right screw jack is touching floor and motorcycle is upright and level. 3) Install left side screw jack on bracket E and adjust out until motorcycle will rest upright on both screw jacks. 4) Adjust screw jacks until motorcycle is level. Place ¾ inch riser under motorcycle rear wheel. Assemble axles, wheels, and fenders onto the tow-pac hitch cart. Push the hitch mount into the receiver hitch.

(this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 5. When removing InstaTrike reverse the above procedure. Adding or removing washers/spacers between receiver hitch and leanstop brace will allow you to level your motorcycle if necessary. Leanstop brace is slotted to allow for proper alignment with bolt holes NOTICE: BOTTOM Be certain that hitch bolts are inserted from the InstaTrike Assembly Diagram.

Wheel Alignment Wheel alignment is critical for proper tire wear and handling. With InstaTrike installed and motorcycle on center stand, measure A and B. Loosen axle plates and align wheel so A and B are equal to within 1/16 of an inch. Tighten axle bolts and torque to 45 pounds. Repeat for C and D.

It may be necessary to shim axle plates for proper alignment. Shortening the adjuster arm raises the trike wheels and places more of the weight of your motorcycle on the motorcycle wheel. This increases motorcycle traction and gives a generally softer ride. 1) Loosen jam nuts 2) Shorten adjuster arm by turning adjuster nut A toward bolt C desired amount.

3) Turn adjuster nut B until it tightens against adjuster bracket and adjuster nut A 4) Tighten nuts A and B and jam nuts Lengthening the adjuster arm lowers the trike wheels and places more of the. Reflector Mounting Instructions Be sure fender is clean and free from dust Do not apply reflectors in direct sunlight or on a hot surface Remove backing from reflector and carefully position on fender. See Diagram Below Lightly spraying back of reflectors with a mild solution of water or Windex will allow easier positioning.

Complete service repair workshop manual for the: Honda VT600C VT600CD VT600 VT 600 Shadow VLX This is the same manual motorcycle dealerships use to repair your bike.

= 0.6 0.6 + 1 = 1.6 1.6 1/1.6 = 0.625 0.625 + 1 = 1.625 1.625 1/1.625 = 0.6154. + 1 = 1.6154. But it takes a long time to get even close, but there are better ways and it can be calculated to thousands of decimal places quite quickly. It is getting closer and closer!